|
||||||||||
|
||||||||||
|
30 Mar 2010, 15:13 (Ref:2663571) | #1 | ||
Racer
Join Date: Mar 2008
Posts: 342
|
Rear axle ride height?
Hi, I am looking for a bit of advice please.
I have just bought a spare Rotax chassis. When swapping my running gear onto it, I have noticed that the rear axle has been raised by about 10mm - lowering the ride height of the kart. I'm keen to try out new set-up's, but will need to re drill stay bars etc to get everything to fit. So before I do, can anyone tell me the likely effect that a lower rear ride height will have on handling? Cheers |
||
|
30 Mar 2010, 19:07 (Ref:2663711) | #2 | |
Rookie
Join Date: Jan 2010
Posts: 15
|
Bearing in mind I stopped racing karts 13 years ago, IIRC Lowering the rear would give more rear end grip which in turn may promote understeer. I'm sure that in the wet I used to lower the front to have the opposite effect (give more front end grip)
With regards your seat mounts and seat stays, I used to (manufacturer reccommended) mount the seat a specific distance from the rear axle, so if your axle is now lower, mount the seat accordingly. Having said that, unless you have a flat bottomed seat you might not be able to go much lower. Like I said it's been a while since I was kart racing, but I hope I may have helped. |
|
|
31 Mar 2010, 07:28 (Ref:2663987) | #3 | |
Rookie
Join Date: Feb 2010
Posts: 81
|
I have not had a Rotax before so I cant help you regarding the fittings etc but in terms of lowering ride height at the rear, firstly I didnt know it was possible on a kart like a Rotax, and secondly, I dont think it's worth it. Firstly obviously if it's too low the bottom of the kart will ground out and not ride kerbs as well, secondly and more importantly, any kart like a Rotax needs to be driven will little rear end grip anyway. too much grip at the rear will start to make the kart hop when going round corners (speaking from my TKM days) and actually a little power slide is faster i.e. requiring less rear end grip.
Hope this mumbled rubbish helps a bit! |
|
|
31 Mar 2010, 08:51 (Ref:2664027) | #4 | ||
Racer
Join Date: Mar 2008
Posts: 342
|
Many thanks both
The chassis I have is prone to excessive oversteer, which is possibly why the previous owner has tried this (bearing hanger brackets have been drilled to accept a higher position). I think you are right Bendy about not having enough ride height, although there are no signs of kerb damage underneath. I am fitting a brake disc protector to be legal for 2010, I think it's going to ground out quite a lot so I'm going to raise the ride height. Rushy, did you used to race Minis? |
||
|
31 Mar 2010, 10:39 (Ref:2664074) | #5 | |
Rookie
Join Date: Jan 2010
Posts: 15
|
||
|
31 Mar 2010, 12:25 (Ref:2664124) | #6 | ||
Racer
Join Date: Mar 2008
Posts: 342
|
I used to race against you in MM back in the day, are you still racing?
The Rotax is good for fitness, but still trying to get my head round driving it, compared to a Mini - I suspect weight isn't helping me I bumped into your dad last year when I was forming up for a race at Brands, he looked like he was enjoying himself. |
||
|
31 Mar 2010, 19:46 (Ref:2664394) | #7 | |
Rookie
Join Date: Jan 2010
Posts: 15
|
Now I'm really confused
I still race, got an MG ZR in the MG Trophy. Rotax was only just starting when I was at the end of my Karting days. I remember that driving a Rotax compared to the ICA (KF2 I think now) that I raced was totally different. If you're worried about weight, I was 6' and 13 stone when I was 15 lost out in the dry, but was awsome in the wet I wouldn't mind having a go in one again as like you say it's definately good for keeping fit. Was that a Classic Sports Car Club meeting by any chance? We're at Brands on the 10th/11th April. |
|
|
4 Apr 2010, 13:26 (Ref:2666596) | #8 | |
Veteran
Join Date: May 2007
Posts: 3,211
|
Oversteer off the corner or entry into the corner? All karts that oversteer off the corner are understeering into it. Get rid of the entry US and the exit OS will not happen.
|
|
|
6 Apr 2010, 13:40 (Ref:2667645) | #9 | ||
Racer
Join Date: Mar 2008
Posts: 342
|
I only ever get understeer in the wet
In the dry, turn-in is neutral, then I get oversteer at the apex and exit, requiring a lot of opposite lock and very delicate application of the throttle to get off the corner with any momentum. Lots of fun, but not particularly quick! Fresh rubber on the rear helps reduce it a bit, as does widening the rear track. So I guess it sound more like a traction issue than balance? |
||
|
7 Apr 2010, 03:37 (Ref:2668032) | #10 | ||
Veteran
Join Date: Jul 2004
Posts: 505
|
Hi Cujo, you want to move the C of G to the rear of the kart to remove that o/steer. Do this by raising the front RH (stub axles down) and keeping the back low (axle up). We had a MS chassis that had terrible o/steer and this totally transformed it.
Try this and adjust rear grip by moving the rear hubs in and out, 3mm at a time until you find the perfect set up. You can also play around with the rear torsion bar too to add/remove grip, horizontal-less, vertical-more. Or move the seat back a bit, you shouldn't have any problems damaging the underneath unless you really do like those kerbs ! Don't forget that in the wet you will want high RH front and back and caster adjusted fully too, naturally rears in and fronts out. |
||
|
7 Apr 2010, 18:37 (Ref:2668393) | #11 | |
Rookie
Join Date: Feb 2010
Posts: 81
|
Can I just interrupt, when doing all this to remove the oversteer, be careful not to go too far, too much rear-end grip is the worst possible thing, especially in a kart like that. It'll start hopping at the rear losing way more time than a bit of power oversteer. A bit of controllable oversteer is the perfect balance that youre looking for. Moving the rears in and out is the best method I found with my TKM that I had. Also, what tyre pressures do you normally run?
|
|
|
8 Apr 2010, 00:56 (Ref:2668564) | #12 | ||
Veteran
Join Date: Jul 2004
Posts: 505
|
Feel free to interrupt anytime bendy .
The chassis that we had the inherent oversteer with was a MS TKM, for this year we have a TALKO TKM, both are completely opposite to each other in their handling characteristics ! With the TALKO we have had to lose rear grip, due to it hopping and gripping up as you described, with the MS we NEVER had any rear grip until we adjusted front and rear ride heights as above. I was just explaining what did the trick for us. Cujo needs a good days testing where he can try all these set ups to suit his kart, whatever his Rotax chassis maybe ? |
||
|
8 Apr 2010, 21:15 (Ref:2669110) | #13 | |
Rookie
Join Date: Feb 2010
Posts: 81
|
I had a TALKO as well, awesome in the wet, but did offer too much grip in the dry, especially at the rear. But as I said before, having too much grip is far worse than having a little too little!
|
|
|
8 Apr 2010, 21:49 (Ref:2669128) | #14 | ||
Racer
Join Date: Mar 2008
Posts: 342
|
Thanks both, yes I understand that it's important to test these tweaks out in one at a time. I'll post how I get on
The chassis is a Deavinson, who I think are no longer in business - from what I can find out, they are great at Rye House, but need a lot of tuning for other tracks |
||
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Bending rear axle for negative camber | david- | Racing Technology | 36 | 25 Apr 2009 09:15 |
Underbody Rake and Ride Height | ckiesz | Racing Technology | 11 | 29 Jan 2008 21:59 |
Ride Height vs Downforce | A. Mudge | Racing Technology | 9 | 11 Jun 2007 20:24 |
Solid Axle vs IRS Rear Suspension | tommurphy73 | Racing Technology | 11 | 9 Nov 2006 11:32 |
Ride height of F3 etc cars | schomosport | Club Level Single Seaters | 45 | 30 Nov 2005 11:54 |