|
||||||||||
|
||||||||||
17 Nov 2003, 14:28 (Ref:785979) | #1 | |
Veteran
Join Date: Apr 2002
Posts: 9,718
|
End Caps
On a ford 4 cyl block, the 'michael rodent' end caps on early precrossflow blocks are prone to breaking under high revs/load, the later square type are better, square steel ones best (I think)
having just had a block line bored with these I have been told that square ones are not eligible for FiA historics someone suggested some fancy Swiss cast iron ones at £500 a set, but quite frankly thats totally out of the question. could I safely modify or make some steel ones to look like standard cast iron ones or would this inherently weaken them (I dont think so) or does anyone have any bright ideas, without remortgaging the house ? thanks Joe |
|
|
17 Nov 2003, 16:28 (Ref:786146) | #2 | |
Veteran
Join Date: Aug 2003
Posts: 2,286
|
Hmmm,
Im not sure if you can modify them as it would not be the cars original "As Manufacture" part. You should try and get a hold of someone in the FIA or the RAC |
|
__________________
Cryos, thats me! To keep the national IQ higher, we prevent links in the signatures. Its clearly in the notice, but that doesn't stop some people moaning about it.. |
17 Nov 2003, 18:02 (Ref:786243) | #3 | |||
Veteran
Join Date: Dec 2001
Posts: 6,359
|
Re: End Caps
Quote:
|
|||
__________________
Doing an important job doesn't make you an important person. |
18 Nov 2003, 13:02 (Ref:787056) | #4 | |
Veteran
Join Date: Apr 2002
Posts: 9,718
|
Thanks for that guys, Dave, I was thinking about blasting them to give the impression of being cast, I dont think the scrutineers are that knowlegeable/strict engineering wise???
the FiA homologation papers say and I quote " heavy duty end caps" now Im no linguist, but thats fairly vague and open to interpretation/debate |
|
|
18 Nov 2003, 14:04 (Ref:787137) | #5 | ||
Veteran
Join Date: Sep 1998
Posts: 2,762
|
Just what are "end caps" and what do they do?
|
||
__________________
Never forget #99 |
18 Nov 2003, 16:19 (Ref:787254) | #6 | |
Veteran
Join Date: Apr 2002
Posts: 9,718
|
they are caps bolted to the block to hold the crank in . . . . and also help make the block a little more rigid
no rocket science invloved really, they just need to be strong, but when the rules are vague with regards to modifications and the standard items are as tough as a French soldier I want to be sure before making any mods. |
|
|
18 Nov 2003, 21:03 (Ref:787594) | #7 | ||
Veteran
Join Date: Sep 1998
Posts: 2,762
|
Duhh! I should have figured it out. We always called them main caps. You might be able to shot blast them to simulate a casting, but you would also need to radius all the sharp edges on the bottom side to make it look more like a casting. It would not hurt to shot blast them anyway as it works to stress relieve the material after machining. We do the main caps and rods this way.
It seems kind of self defeating to insist that main caps (end caps) be of an inferior design. This only promotes more engine failures and can lead to less guys racing in my opinion. I would understand if you make rules to keep things historic, like drum brakes instead of discs, or manual spark advance instead of vacuum advance, etc. But making your lower end bullet proof keeps you on the track and at the races instead trying to sell your car because you can't keep a motor together in it. |
||
__________________
Never forget #99 |
19 Nov 2003, 12:53 (Ref:788154) | #8 | |||
Veteran
Join Date: Dec 2001
Posts: 6,359
|
Quote:
As for scroots.....they are all-seeing, all-knowing, aren't they? |
|||
__________________
Doing an important job doesn't make you an important person. |
19 Nov 2003, 13:20 (Ref:788204) | #9 | ||
Racer
Join Date: Jan 2002
Posts: 207
|
Zefarelly,
How often do the iron caps break? Are you actually gaining an advantage over your competitors by running steel caps? How likely is it that your motor will be protested/stripped for inspection? Probably won't happen unless you win or upset someone badly! If the caps really are a weak point then you might find some of the others are running steel anyway (by mistake, of course!) What revs are you going to limit yourself to? |
||
|
19 Nov 2003, 16:11 (Ref:788391) | #10 | |
Veteran
Join Date: Apr 2002
Posts: 9,718
|
Ive never broken one, but people mention it all the time, I think its mainly the centre cap that goes, if the crank flexes . . . .and I'd suggest anything over 6500 continuously would do it . . . .Ive had chats with various people who have said the big end does let go if you run too high or blip past 8k regularly, given my budget, and the scarcity of some parts, I cant afford to be blowing things up too often . . . .equally I dont want to keep it down and come last !
the Lotu TC guys either use something very expensive or use a steel centre cap. as a safety precaution. I guess I'll do whats safest, and If I get hauled over for it, Ill worry about it then . . .theres certainly no performance gain to be had, if anything the reverse as the steel caps are bigger and heavier ! |
|
|
19 Nov 2003, 18:58 (Ref:788569) | #11 | |
Veteran
Join Date: Oct 2002
Posts: 1,646
|
I wouldn't bet on the scrutineers being unknowledgable.
Don't start crying if you get caught |
|
|
20 Nov 2003, 11:00 (Ref:789249) | #12 | ||
Racer
Join Date: Jan 2002
Posts: 207
|
6500 is not many revs. I expect that the reason the caps break is because they are badly installed or they have an undetected weakness - a crack or stress riser. Cranks should always be crack tested and while you're at it get the rods and caps done. If you clean off all the stress risers from the rods and the mains caps (sharp corners, notches etc) you will really reduce the chances of failure. You will need to have the parts rebalanced if you take metal off (static).
The standard mod for any race engine mains caps was to add a steel strap across the bottom. Is that specifically excluded? BTW shot blasting is different from shot peening. Shot peening is the procedure for strengthening the part - shot blasting for removing scale. Have you asked other competitors what they do? |
||
|
20 Nov 2003, 13:28 (Ref:789479) | #13 | |
Veteran
Join Date: Apr 2002
Posts: 9,718
|
most people wont divulge whats inside, probably because its not strictly speaking legal . . . .I'm not going to be winning anything so I doubt I'll get ripped to shreds every meet, but morally I wont cheat. having said that I'll gladly reinterpret the rules to make sure I can get a reasonable life out of my engine, If it goes bang Im stuffed until I can find the cash for another one.
Ive heard of strapping, although Im not entirely sure what/how to do it. I'd assume something over the bottom of the cap to stop it moving anywhere. having said all that, building my own stuff and developing my own car, its all going to be a bit of trial and error. best apply for another bank loan now ! |
|
|
6 Jan 2004, 23:11 (Ref:829985) | #14 | ||
Rookie
Join Date: Dec 2003
Posts: 21
|
Don't try strapping the main caps, it makes them weaker. Cheapest solution is higher ratio diff and rev limiter. And spend the change on driver tuition!!
|
||
__________________
'Unsafe at any speed' |
10 Jan 2004, 22:34 (Ref:833840) | #15 | ||
Veteran
Join Date: Jun 1999
Posts: 727
|
hmmm
i think in the interests of safety u should upgrade them of course not strictly ok, but regs are vauge so not too bad, you could agru it completley. if they are they unreliable then change um, but then if you over rev any engine for a while, then summin gotta break!! |
||
|
13 Jan 2004, 22:01 (Ref:837187) | #16 | ||
Racer
Join Date: Nov 2003
Posts: 218
|
Can you get in touch with a scruterneer through your club or the msa? or is it best to not draw attention to the issue. Just a thought.
|
||
__________________
"if you aint pushin'it you might as well be pullin'it" |
14 Jan 2004, 06:54 (Ref:837535) | #17 | ||
Veteran
Join Date: Jul 2002
Posts: 1,994
|
Speak to a foundry and see if you can get some cast out of a better grade CI???? or steel for that matter.If they look cast the scutineers probally wont go near them.You know the saying "Looks like a duck,quacks like a duck-probally is a duck".They would be able to make them slightly strongher by adding material in a few criitcal places also. You may be able to get a few competitors to buy a set as well to reduce the cost.Equally an engine builder in the class may be interested in getting a few.
Maybe heat treatment etc.Failing that getting some crack testing done on a regular basis.Are you allowed to get the components better balanced to reduce the load? Your only cheating if your coaght anyway |
||
|
14 Jan 2004, 13:05 (Ref:837856) | #18 | |
Veteran
Join Date: Apr 2002
Posts: 9,718
|
It would appear that some posh Swiss company make rediculously expensive ones (£100 each !!!) I got a set of steel ones on Ebay for £50, the rules are hideously vague and I wont be winning anything, but I cant afford to rebuild my engine too regularly
I think most people have non original typess, purely for safety and reliability, it has no direct effect on performance, bit of a stupid rule if you ask me. |
|
|
14 Jan 2004, 15:44 (Ref:838049) | #19 | ||
Rookie
Join Date: Dec 2002
Posts: 93
|
If they have already been machined they will be no good as they need to be line bored to your block. Any worthwhile engine builder can supply them.
|
||
|
14 Jan 2004, 16:07 (Ref:838091) | #20 | |
Veteran
Join Date: Apr 2002
Posts: 9,718
|
they havent, but have now, with an ARP stud kit. I think they where just new old stock . . . .and at half price, good enough for me.
|
|
|
14 Jan 2004, 17:05 (Ref:838171) | #21 | ||
Rookie
Join Date: Dec 2002
Posts: 93
|
I don't think you should underestimate the scrutineers though at International level , when I was last at Monza the winner got disqualified because he had titanium valve caps instead of steel.
|
||
|
15 Jan 2004, 01:49 (Ref:838738) | #22 | ||
Racer
Join Date: Jan 2002
Posts: 207
|
Have you called the championship technical person/eligibility scrutineer and asked what the accepted position is?
|
||
|
15 Jan 2004, 04:20 (Ref:838845) | #23 | |||
Veteran
Join Date: Jul 2002
Posts: 1,994
|
Quote:
|
|||
|
15 Jan 2004, 09:19 (Ref:838996) | #24 | |
Veteran
Join Date: Apr 2002
Posts: 9,718
|
the same goes for roller rockers, lightened pushrods etc . . .lightened valve train has a marked effect in performance and engine acceleration, dead easy to spot as well without major surgery!
|
|
|
6 Feb 2004, 19:03 (Ref:865708) | #25 | ||
Veteran
Join Date: Jan 2004
Posts: 1,254
|
if your having problems with end caps your clearly doing something seriously wrong, i assume we are talking kent engine here???
in standard ff1600 cam config (as per historics and any other kent series) the cam must remain the GT type and as such runs out of breathe past about 6k, so theres no point taking it that high, theres no power up there thats for sure, so you'd be better to run different gearing and make use of the bulgy bit of the power and torque curve before they go down again. if you and your mates keep blipping it to 8k then consider- a) lessons in using a gear leaver to prevent over revs on the downshift b) a rev limitter (also know as a nice bit of common sense..) to prevent taking it to 8k, it impresses absolutely no one in the paddock when someone sits there flogging the bolarks off there engine before/after the race... i was of the understanding that any kent crossflow engine is the same for ff, i.e the engine regs are the same, i may be wrong but cant you just uses a later block with the better main caps fitted as standard? |
||
__________________
never eat belly button fluff |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
A Few In-Game Video Caps... | TerryC | Virtual Racers | 10 | 14 Sep 2003 09:32 |
Salary Caps: Could it... work? | golem | Formula One | 31 | 15 Nov 2002 22:41 |
Malboro Caps | Ed G | ChampCar World Series | 5 | 1 Jun 2001 05:37 |