|
||||||||||
|
||||||||||
22 Jul 2004, 09:59 (Ref:1042973) | #1 | |
Veteran
Join Date: Apr 2002
Posts: 9,710
|
condensers
how do they work ? how can you test one, and why did mine clap out on the start line on Sunday?
I'm trying to think of a reason why it just died, no warning and no apparent reason . . . .the car was perfect up to that point . . .could it have been damaged by the scrutes making me hit over 3k revs then yanking the cut out switch ? a dodgy rev counter ? or just my bad luck at Brands ? |
|
|
22 Jul 2004, 13:29 (Ref:1043397) | #2 | ||
Veteran
Join Date: Oct 2003
Posts: 871
|
I don't know how they work, but you can pick one up from the workshop floor and it will work for years or be let down by a new one! I think they are sensitive to voltage.. if the wrong coil is used they don't last.
Don't your regs allow electronic ignition? Last edited by StephenRae; 22 Jul 2004 at 13:30. |
||
|
22 Jul 2004, 19:54 (Ref:1043807) | #3 | |
Rookie
Join Date: Jul 2004
Posts: 8
|
A capacitor, or condenser as it used to be called,is a device for storing electricity for a limited time.
On your engine it is used for spark quenching,i.e to prevent arcing at the points. In a points operated ignition system, self-induction causes a high voltage sufficient to produce a spark across the points at the instant they open. Fitting a capacitor in parallel with the points allows the energy to be momentarily absorbed. When the capacitor discharges, the gap at the points is too large for arcing to occur. If the capacitor fails in most case's the primary voltage travels straight to earth,no spark and quite often as in your case no warning. As Steve recomends check your regs and if its allowed fit an after-market electronic system. This will get rid of the capacitor and in most cases give you a variable dwell angle, two big advantages. hth |
|
|
23 Jul 2004, 08:29 (Ref:1044264) | #4 | |
Veteran
Join Date: Apr 2002
Posts: 9,710
|
thanks chaps, I'm not sure we're allowed electronic ignition (for FiA regs) . . . .I have it waiting in the wings though!
as you say . . .a 2nd hand one out of an old box of bits is fitted and the car sprang to life . . . .unfortunately I couldnt do it on the grid ! |
|
|
26 Jul 2004, 09:32 (Ref:1047478) | #5 | |
Veteran
Join Date: Apr 2002
Posts: 9,710
|
someone suggested using a lower voltage coil and a ballast resistor . . .apparently it'll prolong condenser life, can anyone verify that ?
electrical stuff does my head in ! |
|
|
26 Jul 2004, 09:52 (Ref:1047492) | #6 | ||||
Veteran
Join Date: Dec 2001
Posts: 6,358
|
Quote:
Quote:
Last edited by Dave Brand; 26 Jul 2004 at 09:53. |
||||
__________________
Doing an important job doesn't make you an important person. |
26 Jul 2004, 14:42 (Ref:1047821) | #7 | ||
Veteran
Join Date: Apr 2002
Posts: 9,710
|
Quote:
I might just stick a spare in the glove box just in case ! |
||
|
26 Jul 2004, 23:33 (Ref:1048329) | #8 | |||
Ten-Tenths Hall of Fame
Veteran
Join Date: Aug 2002
Posts: 1,837
|
Reliability
Quote:
|
|||
__________________
No trees were harmed by this message. However, several million electrons were terribly inconvenienced |
27 Jul 2004, 17:00 (Ref:1048975) | #9 | |||
Race Official
Veteran
Join Date: May 2004
Posts: 2,479
|
Re: condensers
Quote:
|
|||
|
27 Jul 2004, 19:15 (Ref:1049105) | #10 | ||
Veteran
Join Date: Mar 2003
Posts: 3,523
|
The trick is to connect the alternator to the battery, and then the alternator always has a load on it. The simple cut-out still works in the normal way. Shall I draw a picture? It's far easier that those unreliable FIA switches (which have cost me lots of points in the past!), and fully effective.
Condensers, capacitors, easily tested. Just buy a multi-meter with a capacitor test facility. Most condensers have their capacitive values on them. They should be within 10% I would expect. It's sometimes quicker to change it for a new one than take it off and test it, and let's face it, they are not exactly expensive. Rob. Rob |
||
__________________
There is no substitute for cubic inches. Harry Belamonte - 403ci Vauxhall Belmont!! A 700hp wayward shopping trolley on steroids!! |
28 Jul 2004, 07:50 (Ref:1049522) | #11 | |||
Race Official
Veteran
Join Date: May 2004
Posts: 2,479
|
Quote:
Wouldn't say the simple ones are any more reliable. I used to have one on my current car and had to send it back for randomly shutting down my electrics during a race weekend |
|||
|
28 Jul 2004, 11:39 (Ref:1049731) | #12 | |
Veteran
Join Date: Apr 2002
Posts: 9,710
|
I have an Fia switch but dont trust it ! the alternator feeds the solenoid direct, I guess I could send it straight to the battery then its always got something to charge, good thinking. the FiA switch cuts the coil quick enough though.
|
|
|
4 Aug 2004, 10:21 (Ref:1055961) | #13 | |
Rookie
Join Date: May 1999
Posts: 46
|
I should probably start a new topic for this, but this one seems well developed...
Just fitted an AIM data logger into a FF1600 and everything is dandy, until you look at the RPM while the engine is running. It jumps all over the place. I now know that AIM make an "RPM-ECU Interface Module", however, that will not help me tomorrow. I'm lead to believe that a capacitor will help smooth things out, and so I tried sticking an old condensor into the wire between the Coil -ve and the Logger. Blow me down if it didn't work... ... until the revs got up around 4000 or above. Then it starts jumping around again. So my question is- is this because the condensor/capacitor I chose wasn't up to the task, and if so, what sort of capacitor should I be looking to stick into the system (running standard FF points, not these flash electronic units that we aren't allowed)? And if the condensor should have done the job, what else might I be able to do? |
|
|
4 Aug 2004, 11:28 (Ref:1056031) | #14 | |||
Veteran
Join Date: Jul 2002
Posts: 3,499
|
Free Advice - No Responsibility Accepted!!!
Quote:
|
|||
__________________
The good old days sure seem like a long time ago!! |
4 Aug 2004, 12:19 (Ref:1056075) | #15 | |
Rookie
Join Date: May 1999
Posts: 46
|
It's gotta be worth a go. If one is good, two must be better.
Should I be chucking any sort of resistor in there just for good measure? (Don't ask me why, I don't know, but I feel it would make the whole thing look more impressive, and that's what really counts...) |
|
|
4 Aug 2004, 12:30 (Ref:1056092) | #16 | |
Veteran
Join Date: Apr 2002
Posts: 9,710
|
if you run 2 condensers won't you be sapping power from the spark plugs ??? ( I don't know either!)
the revs jumping around is almost definitely points bouncin . . .mine does the same on the rolling road with a digital strobe gun on it, possibly why I had so much trouble with rev counters ! |
|
|
4 Aug 2004, 12:49 (Ref:1056104) | #17 | |
Rookie
Join Date: May 1999
Posts: 46
|
Will look into the points, zefarelly. There'll be no bouncin on MY shift.
Have just read more words of wisdom, and there is some talk that place a 10k ohm 1/2 watt resistor between coil and tacho pickup wire could solve the problem. The plot thickens..... |
|
|
4 Aug 2004, 13:27 (Ref:1056145) | #18 | |||
Veteran
Join Date: Jul 2002
Posts: 3,499
|
Dropping Resistor....
Quote:
Condensers do not pass DC current, therefore they will pass pulses but serve to clip them in their prime!! Its the pulses either finding a path into the wrong part of your black box or the points are a bouncin....let us know!! |
|||
__________________
The good old days sure seem like a long time ago!! |
4 Aug 2004, 17:14 (Ref:1056327) | #19 | ||
Race Official
Veteran
Join Date: May 2004
Posts: 2,479
|
Got rid of all those sort of probelems by fitting Luminition optical points and electronic amplifier. This mod usually complies with "non-managed spark" rules as it can't be programmed or adjusted other than in the usual way for dizzy timing. Needs fully suppressed ht leads though. :-)
|
||
|
5 Aug 2004, 07:37 (Ref:1056747) | #20 | |
Veteran
Join Date: Apr 2002
Posts: 9,710
|
Dtype38 . . .do you think thats acceptable for FiA historics ? It doesnt say you specifically can't use points although I was under the impression you had to stick with the original . . . .
what would the resistor in line with the tacho do ? |
|
|
6 Aug 2004, 14:45 (Ref:1058330) | #21 | ||
Race Official
Veteran
Join Date: May 2004
Posts: 2,479
|
I would only be guessing about the FiA Historic Rules, but its acceptable as original equipment for 1950s-on Jaguar Sports car and Saloon racing with the JEC because the spark is still generated by "distributor points" and cannot be mapped or adjusted. May help to know that the technical name for the Luminition System is "Optical Points" so it still counts as having "Points" but you'll need to check with specific rules if they have to be "Contact Breaker" type (traditional).
As for a resistor in line with the tacho, I run an electronic tacho in line with the supply to the coil. It works by sensing the tiny voltage blips as the coil fires and needs all the signal it can get. A resistor in series would reduce the coil voltage and damp the signal so would definitely be a no-no for my car. Trouble Unfortunately there are probably lots of variations on tacho and coil wiring and I'm not an expert. |
||
|
6 Aug 2004, 14:50 (Ref:1058338) | #22 | |||
Race Official
Veteran
Join Date: May 2003
Posts: 11,142
|
Quote:
|
|||
|